Is Your Arlo Camera Flashing Orange? Try These Solutions!

An LED light is present on the front face of the Arlo camera. Its purpose is to deliver messages regarding the status of your wireless security camera. It does so by flashing various colors and orange is one of them. If your Arlo camera flashes the orange color, then you must know that your rapt attention is needed. Why do you need to pay attention and if there is something wrong when the Arlo camera flashing orange situation shows up? The same has been discussed in this write-up. But, before all else, let us find out why the security device illuminates orange color.

Why is Arlo Camera Flashing Orange?

To be true, there is no such color flashed by the LED light located on the front face of the camera. However, some users mistake the amber color for orange and end up concluding that their camera’s light is showing the orange color. The color amber or orange appears in three scenarios which are listed below:

• Slow Flashing Orange: If you notice your camera slowly flashing the color orange, it simply means that your camera is not found by the Base Station or the camera is out of the network range during the Arlo camera setup process. It also suggests that a connection error has occurred during the camera and Base station pairing process. Lastly, a low battery percentage is also indicated by the orange color.
• Fast Flashing Orange: If the Arlo camera flashing orange situation shows up but the light flashes at a faster rate, then it means that the sync between the security camera and the Arlo SmartHub or Base Station has failed. In case you have none of these devices and are trying to connect your camera to the WiFi network, the orange color represents the connection failure.
• Alternating Orange plus Blue: When the camera’s LED light shows the color orange and blue alternatively, it simply means that the firmware update is being carried out. Just in case the LED remains in the same situation for a longer period, it is a sign that the firmware update process is taking longer than usual. It happens when the internet connection is not up to the mark.

Is the Arlo Camera Flashing Orange Situation an Issue?

The previous section covered the different situations when the Arlo camera flashes orange. You can easily conclude that whenever the Arlo camera flashing orange situation shows up, it simply means that there’s an issue. With that being said, you are advised to be prepared to implement a few troubleshooting techniques that have been highlighted in the upcoming section. You might also need your Arlo login details while executing the troubleshooting process. So, be ready.

Resolutions: Arlo Camera Flashing Orange

Since the messages conveyed by the LED light of the camera were different in all situations, the troubleshooting techniques also varied. Walk through the below-given information to know what to do to resolve the problem:

Reduce the Gap (Slow Flashing Orange)

When the camera flashed orange slowly, it was due to the connection problem between the Arlo camera and the host networking gadget. In 90% of the cases, users connect their devices wirelessly and such connections are likely to get impacted by interference too soon. Thus, always make sure that the distance between your security camera and the Arlo SmartHub or Base station is less. In case you cannot bring them closer, try to reduce physical impedances between their paths of communication. Also, charge the battery.

Re-sync Your Devices (Fast Flashing Orange)

Lesser frequencies of the Arlo camera flashing orange situation was a sign of connection failure between the SmartHub and the camera. It means that apart from reducing the gap separating them, the user is supposed to sync them again. For this, the Sync button present on both devices needs to be pressed. But, remember to press the Sync button on the second device within 2 minutes of doing the same on the first device. After re-syncing your security and networking device, check the LED status.

Let Your Device Update (Blue and Orange)

When the device was showing orange and blue color alternatively, it was a sign that the firmware of the device was being updated. You are only supposed to wait till the process gets completed. However, checking the internet connection is recommended if the firmware update is taking longer than usual. Know that the update will fail if you don’t pay attention and features like Arlo Geofencing are likely to get non-working in that case.

The Final Note

The Arlo camera flashing orange situation is really a matter of concern. But, as you can see, keeping a check on connections will help you address the problem very easily. Now, we are hopeful that you will be able to fix the issue.

Just in case you own an Arlo Pro 5S it flashes the orange color 4 times and then stops, then know that the factory default reset process has been triggered. You must wait and reconfigure the camera as soon as the reset process finishes.