Ultra 2 Won’t Work with Battery Connected? How to Resolve?
Rolled out 23rd October 2023, the Ultra 2 won’t work with battery connected issue has managed to frustrate a number of users due to which they are unable to do Arlo login. They have been complaining that the Ultra 2 camera is refusing to work properly even when the battery is connected. In case you too are losing your mind because of the same issue, then walking through the information provided in this blog post will be great for you.
Why Ultra 2 Won’t Work with Battery Connected?
Before jumping to the section consisting of the solutions to resolve the Ultra 2 won’t work with battery connected issue, you should understand what could have caused it. Some of the reasons have been highlighted here:
1st Reason: The first reason is the existence of technical glitches.
2nd Reason: Your camera is not receiving an adequate power supply.
3rd Reason: The battery which is connected to the camera is not charged.
4th Reason: The battery is demanding to be replaced.
Now that you have filled your brain with the knowledge regarding the reasons behind the issue at hand, read the solutions presented in the following section and learn how it can be put to an end in a matter of minutes.
How to Fix Ultra 2 Won’t Work with Battery Connected?
1st Solution: Restart the Arlo Ultra 2
As mentioned above, the very first reason why you are experiencing the Ultra 2 won’t work with battery connected issue is because of the existence of technical glitches. But, you should not think much about getting rid of them as it is quite easy.
You just have to make the effort of restarting or rebooting your camera. By the way, this can also help one fix the Arlo camera setup issues. Anyway, the question is how to give the camera a new start. To answer it for you, we have mentioned the steps in the next section.
Locate and press the power button on the camera, wait for some time, and then press the button again, but this time to turn on your networking device. Now, check in case the issue in discussion has left following you around.
2nd Solution: Check the Power Socket
Considering you have already made your way to the second troubleshooting tip, means that you are still experiencing the Arlo Ultra 2 camera won’t work with battery connected issue. To take care of it, check the wall socket to which you have connected it.
Any damages are found? Is the socket short-circuited? Whatever the scenario may be, you should get the wall socket repaired by calling an experienced electrician at your place. In case he says that the wall socket is beyond repair, then you should try a different approach.
Another approach requires you to consider plugging your Arlo Ultra 2 camera into another socket. Make sure that this one is non-damaged if not anything else. Otherwise, you will continue to face the issue that you have been facing.
3rd Solution: Charge the Camera Battery
Despite reading the 1st and 2nd troubleshooting tips, are you still experiencing the Ultra 2 won’t work with battery connected issue? Well, in that case, you ought to charge the camera battery without wasting any more time.
In order to do the same, you can use a USB charging cable that you received when you were unwrapping the camera. Connect the cable to the USB charging port. This can be done if pull the flap at the bottom of the camera.
Now, let the device get charged. It is recommended that you do not interrupt the process by powering down the camera. For your information, depending on the requirement of your device, the time of the charging process might vary.
4th Solution: Replace the Camera Battery
The Ultra models are made of two parts. The camera and battery are together in one part and the camera housing acts as a protective shell in the second part. Replacing the battery of the camera requires you to remove the camera from the camera housing.
In order to change the battery in the camera, you need to remove the battery by pulling on it until it slides out of the camera. Align the new battery and insert it into the compartment of the battery. Now, wait for the camera LED to blink blue.
Once done, insert the camera back into the camera housing and make sure that clicks into place. This can be initiated by you if you push down on both the left as well as the right side of the camera that you are using at the moment.
Wrap Up
With the hope of helping you out, we are wrapping up the blog post discussing how the Ultra 2 won’t work with battery connected issue can be resolved with ease. We hope that now you will be able to make the most of your camera via the Arlo app remotely.
